Victron Lynx Smart BMS 500 NG (M10)
- Brand:
- Victron Energy
- Part no:
- LYN034160310
Image: Victron Energy
Where to buy
Specifications
- Type
- Bms
- System voltage
- 12V, 24V or 48V
- Works with
- Victron Lithium NG batteries
- Continuous rating
- 500 A
- Bluetooth
- Yes
Manuals and data sheets
- Lynx Smart BMS NG manual (HTML)www.victronenergy.com
- BMS NG Overview data sheet manual (PDF)www.victronenergy.com
- Lynx Smart BMS NG data sheet manual (PDF)www.victronenergy.com
Full data sheet
Victron Energy, part number LYN034160310
Technical
- Power consumption in standby mode
- Approximately 2.6W (217mA at 12V) depending on the state of the relays
- Allow-to-discharge port maximum current rating
- 0.5A at 60VDC, protected by resettable fuse
- AUX output maximum current rating
- 1.1 A continuous, protected by resettable fuse
- Busbar Dimensions
- 8mm x 30mm
- Busbar material
- Tinned copper
- Current rating (continuous)
- 500 A
- Peak current rating (5 minutes)
- 600 A
- Maximum humidity (non-condensing)
- 95 %
- Maximum input DC voltage
- 75 V
- Operating temperature range
- -40 to 60 °C
- Power consumption in OFF mode
- 0.3mA for all system voltages
- Power consumption in ON mode
- Approximately 4.2W (350mA at 12V) depending on the state of the relays
- Minimum load resistance for pre-charging
- 10Ω and above for 12V systems 20Ω and above for 24V and 48V systems
- Programmable relay
- SPDT - 2 A at 60 VDC
- Reverse polarity protection
- No
- Storage temperature range
- -40 to 60 °C
- Supported system voltages
- 12V or 24V or 48V
- Operational DC voltage range
- 9 to 60 V
- Allow-to-charge port maximum current rating
- 0.5A at 60VDC, protected by resettable fuse
Connections
- VE.Can
- RJ45
- Lynx Distributor fuse monitoring (up to 4 modules)
- RJ10 (RJ10 cables ship with each Lynx Distributor)
- I/O terminal
- Removable multi-connector with screw terminals
- Busbar connections
- M10
- Battery communication terminals
- Terminals with M8 circular connectors
Enclosure
- Width
- 180 mm (7.1 in)
- Weight
- 1.9 kg (4.2 lb)
- Protection category
- IP22
- Color
- Blue (RAL 5012)
- Depth
- 80 mm (3.1 in)
- Height
- 190 mm (7.5 in)
- Material
- ABS
Standards
- quality (QMS)
- NEN-EN-ISO 9001
- Safety
- EN-IEC 63000
- Emission / Immunity (EMS)
- EN-IEC 61000-6-3
The Lynx Smart BMS 500 NG (M10) is a battery management system for Victron Lithium NG batteries. It has a 500 A continuous rating with a 600 A peak for 5 minutes, and it supports 12V, 24V or 48V systems. A built-in contactor allows remote-controlled main switching, a pre-alarm signal comes ahead of a low cell voltage shutdown, and setup is over Bluetooth through the VictronConnect app. Standby draw is approximately 2.6W, and there is no reverse polarity protection.
Our take
With a 500 A continuous rating and a 600 A five-minute peak, the Lynx Smart BMS 500 NG sets the current its built-in contactor can carry. It has no reverse polarity protection, so the battery cables have to be connected correctly the first time.
From our buying guide
BCI defines a battery management system as an electronic system that monitors a battery's condition, performance and health. Some lithium batteries have one built in and some need an external unit.
Check before you buy:
- Battle Born warns that a BMS shutdown leaves the vessel without power, and that one during alternator charging can severely damage the alternator.
- There is no one low-temperature limit for charging lithium, so take it from the manual for the battery you have.