Victron Lynx Smart BMS 1000 (M10)
- Brand:
- Victron Energy
- Part no:
- LYN034170210
Image: Victron Energy
Where to buy
Specifications
- Type
- Bms
- Works with
- Victron Lithium Smart batteries
- Continuous rating
- 1000 A
- Bluetooth
- Yes
Manuals and data sheets
- Lynx Smart BMS manual (HTML)www.victronenergy.com
- Instant Readout manual (HTML)www.victronenergy.com
- BMS Overview data sheet manual (PDF)www.victronenergy.com
- Lynx Smart BMS data sheet manual (PDF)www.victronenergy.com
- VictronConnect app manual (HTML)www.victronenergy.com
Full data sheet
Victron Energy, part number LYN034170210
Technical
- AUX output maximum current rating
- 1.1 A continuous, protected by resettable fuse
- Busbar Dimensions
- 8mm x 30mm
- Busbar material
- Tinned copper
- Allow-to-discharge port maximum current rating
- 0.5A at 60VDC, protected by resettable fuse
- Current rating (continuous)
- 1,000 A
- Peak current rating (5 minutes)
- 1,200 A
- Maximum humidity (non-condensing)
- 95 %
- Maximum input DC voltage
- 75 V
- Operating temperature range
- -40 to 60 °C
- Power consumption in OFF mode
- 0.3mA for all system voltages
- Power consumption in ON mode
- Approximately 4.2W (350mA at 12V) depending on the state of the relays
- Power consumption in standby mode
- Approximately 0.6W (50mA at 12V)
- Minimum load resistance for pre-charging
- 10Ω and above for 12V systems 20Ω and above for 24V and 48V systems
- Programmable relay
- SPDT - 2 A at 60 VDC
- Reverse polarity protection
- No
- Storage temperature range
- -40 to 60 °C
- Supported system voltages
- 12V or 24V or 48V
- Operational DC voltage range
- 9 to 60 V
- Allow-to-charge port maximum current rating
- 0.5A at 60VDC, protected by resettable fuse
Connections
- Battery communication terminals
- Terminals with M8 circular connectors
- I/O terminal
- Removable multi-connector with screw terminals
- Busbar connections
- M10
- Lynx Distributor fuse monitoring (up to 4 modules)
- RJ10 (RJ10 cables ship with each Lynx Distributor)
- VE.Can
- RJ45
Enclosure
- Width
- 180 mm (7.1 in)
- Material
- ABS
- Height
- 230 mm (9.1 in)
- Depth
- 100 mm (3.9 in)
- Color
- Blue (RAL 5012)
- Weight
- 2.7 kg (6.0 lb)
- Protection category
- IP22
Standards
- Safety
- EN-IEC 63000
- Emission / Immunity (EMS)
- EN-IEC 61000-6-3
- quality (QMS)
- NEN-EN-ISO 9001
The Lynx Smart BMS 1000 (M10) is a battery management system made for Victron Lithium Smart batteries. It is rated for 1,000 A continuous and 1,200 A for 5 minutes, and works on 12 V, 24 V or 48 V systems. It has Bluetooth for VictronConnect setup and monitoring, M10 busbar connections and a 2.7 kg enclosure. There is no reverse polarity protection.
Our take
The 1,000 A continuous rating with a 1,200 A five-minute peak sets a high current ceiling for the bank, but there is no reverse polarity protection, so check battery cable polarity twice before connecting.
From our buying guide
BCI defines a battery management system as an electronic system that monitors a battery's condition, performance and health. Some lithium batteries have one built in and some need an external unit.
Check before you buy:
- Battle Born warns that a BMS shutdown leaves the vessel without power, and that one during alternator charging can severely damage the alternator.
- There is no one low-temperature limit for charging lithium, so take it from the manual for the battery you have.